VIBRO-BED^TM干燥机，冷却器和保湿机
完整的圆振动流化床系统橇装式已经准备好处理

在更小的空间，更高的性能，更低的成本比以往任何时候都可能

凯胜流化床干燥机，冷却器，和保湿剂使用创新的圆形处理单元，它本质上是更强，更轻，成本更低的建设和完成卫生标准比具有相同表面积的矩形单元。
由于循环流化床处理器也更紧凑的，完整的流化床系统可以预先设计和脚轮搭载帧上预先配置的，准备好用于安装和启动。
此外，凯胜循环流化床的处理器保持一个^的水平，运行效率，在很宽的范围内的模型尺寸从18英寸到84英寸（4602540毫米），直径在实验室和试验厂测试以及批量或大批量的行干燥，冷却，或散装食品，药品和化学品的保湿。

连续的空气流和振动分离和流态化单个粒子，材料的表面积^大化，并相应的速率干燥，保湿，加热，或冷却，可能会发生。
为了防止流化床颗粒的^上部层被拉入废气流中，流体床排气压力通风系统锥形向外，有效地降低了50％的空气流速。

的振动运动的处理器还用于传达沿着一条限定的通道的材料上的“先入/先出”的基础上的统一的处理，并在每个周期结束时疏散流化床。
为适合您的材料应用和整合现有的厂房设备，凯胜提供全面的设备组件，子系统或完整的系统，可作为。

供应端组件：
离心式风机
空气过滤器
电取暖器
油或燃气加热器
蒸汽盘管
冷水机组/热交换
加湿器
管道和阀门
空气流量计和自动化控制

排气侧部分组成：
管道系统
旋风分离器与旋转阀
袋的房子排风机

流化床部分组成：
与本活化剂和旋转阀的储存箱，
振动或螺旋给料机（料仓以^体床处理器的定位时不必要的）
包括进气和排气全会，柔性接头，快速断开罩，圆形屏幕，偏心电机驱动器，弹簧悬架的振动流化床处理器
振动，钻，气动出料输送机
液位传感器和自动化控制

VIBRO-BEDTM DRYERS, COOLERS AND MOISTURIZERS
complete circular vibratory fluid bed systems skid mounted ready to process

Greater performance in less space at lower cost than ever before possible

Kason fluid bed dryers, coolers, and moisturizers employ an innovative circular processing unit which is inherently stronger, lighter, and less costly to build and finish to sanitary standards than rectangular units having equivalent surface area.
Because the circular fluid bed processor is also more compact, complete fluid bed systems can be pre-engineered and pre-configured on caster-mounted frames, ready for installation and start up.
Moreover, Kason circular fluid bed processors maintain an unprecedented level of operating efficiency across a wide range of model sizes from 18 to 84 inches(460-2540mm) in diameter for laboratory and pilot plant testing as well as batch or high-volume in-line drying, cooling, or moisturizing of bulk foods, pharmaceuticals, and chemicals.

Continuous air flow and vibration separate and fluidize individual particles, maximizing the surface area of material and, accordingly, the rate at which drying, moisturizing, heating, or cooling can occur.
To prevent the uppermost layers of fluid bed particles from being pulled into the exhaust stream, the fluid bed exhaust plenum tapers outward, effectively reducing the air velocity by 50 percent.

The vibratory motion of the processor also serves to convey the material along a defined pathway for uniform processing on a "first in/first out" basis, and to evacuate the fluid bed at the end of each cycle.
To fit your material application and integrate with existing plant equipment, Kason offers a comprehensive range of equipment available as components, sub-systems, or complete systems.

Supply side components:
Centrifugal Fans
Air Filters
Electric Heaters
Oil- or gas-fired heaters
Steam coils
Water chillers/heat exchanges
Humidifiers
Ductwork and Valves
Air flow meters and automated controls

Exhaust-Side components:
Ductwork
Cyclone separator with rotary valve
Bag house with exhaust blower

Fluid bed components:
Storage bin with bin activator and rotary valve
Vibratory or auger feeder (unnecessary when surge bin is positioned above fluid bed processor)
Vibratory fluid bed processor including intake and exhaust plenums, flexible couplings, quick-disconnect cowl, circular screen, eccentric motor drives, and spring suspension
Vibratory, auger, or pneumatic discharge conveyor
Level sensors and automated controls